SKIP-1, SKIP-2 are the posts of permanent test stations which commutate measurement and power circuits of electrochemical protection devices, they measure the differential and polarized potentials, here troubleshooting devices are connected, and protected underground facilities, utilities, reservoirs are monitored. The equipment is used to control the quality of electrochemical protection system in gas, oil and other areas.
More than 100 different models of the posts are used at the cathodic protection stations, for the route, anodic and drainage test stations. The posts on the routes are located at a particular distance from each other and at the crossings with the roads, water barriers and other utilities.
Post Design
A post consists of a steel tube part, footing plate, tube welded panels with the measurement and power terminals, a hinged cover. The latter hides terminal panels. The cover has two sloping planes to apply the identification details and two locks to close the panels. Terminal panels are designed with different numbers of the terminals to vary the combinations of power and measurement terminals. A terminal set can be both standard and customized depending on the equipment maintenance. A Post SKIP-1 with the standard combination and number of the terminals has up to 24 measurement and up to 8 power terminals; measurement + power terminals – 12+4. Standard combination and number of terminals for SKIP 2 are up to 48 measurement and up to 16 power terminals; measurement + power terminals – 24+8.
Post weights vary from 23 up to 32 kg, and its heights differ from 2 to 2.5 m. SKIP is equipped with additional lights, if any, which is necessarily written in the device documentation. The Posts are installed in the open air and on the surface and can operate at -50 — +50 °С.
EHZ-CENTER offers the best price on SKIP-1, SKIP-2. We cooperate with reliable suppliers, the products are certified.
A guide price for the Posts SKIP-1, SKIP-2 is from ₽ 2,900. Check the price and leave your request at 8-800-250-11-83 or send a request at
exportehz@gmail.com.
Posts of Test Stations
В зависимости от применения, в надземные стойки стационарных контрольно-измерительных пунктов СКИП-1 и СКИП-2 выводятся проводники от протекторов, датчиков потенциалов, электродов заземления анодных, кожухов подземных конструкций и других защищаемых ЭХЗ объектов.
Различие стоек стационарных контрольно-измерительных пунктов типов 1 и 2 состоит в количестве вертикальных клеммных панелей. В СКИП-1 панелей размещается 2 шт., в СКИП-2 — 4 шт. Следовательно, стойки разнятся по числу клемм, весу и диаметру пунктов.
Работы по монтажу стоек на объекте включают ряд действий.
- Согласно проекту, разбивают местность по точкам расположения стоек.
- Роют котлован.
- Протягивают кабели в пункты. Кабели, провода и клеммы маркируются строительно-монтажной организацией в соответствии с запроектированной схемой соединения.
- Устанавливают стойки СКИП-1 или СКИП-2 в котлован и засыпают послойно грунтом, уплотняя каждый слой.
- Подсоединяют контролируемые элементы ЭХЗ кабелями / проводами к измерительным и силовым клеммам КИП при наличии разрешения и в присутствии представителей эксплуатирующих предприятий.
- Наносят порядковый номер КИП краской.
- В радиусе 1 метра закрепляют почву вокруг стоек.
You are welcome to attach any draft documents (a project), if any, to your request.